How to send email using rsendas and rsendasmessage

[xhsoldier]

code also like send sms, but where should be modified?
Do I need to configure the pop and Smtp protocals
How should I do to send email using rsendas, pls give me some instruction steps.

RSendAs sendAs;
User::LeaveIfError(sendAs.Connect());
CleanupClosePushL(sendAs);

RSendAsMessage sendAsMessage;
sendAsMessage.CreateL(sendAs, KUidMsgTypeSMS); //KUidMsgTypeSMS change to waht?
CleanupClosePushL(sendAsMessage);

// prepare the message
sendAsMessage.AddRecipientL(_L("xhsoldier@hotmail.com"), // right?
RSendAsMessage::ESendAsRecipientTo);
sendAsMessage.SetBodyTextL(_L("aMessageBody"));

// send the message
sendAsMessage.SendMessageAndCloseL();
//where to attach the attachment?

// sendAsMessage (already closed)
CleanupStack::Pop();

sendAs.Close();
// sendAs
CleanupStack::PopAndDestroy();

[xhsoldier]

Waiting for the answer online,
does sending email relate with the creating account.
I really do not know what is account used for?

[xhsoldier]

Nobody knows this!!!!!!!!!!!!!!!!!

[xhsoldier]

Why? nobody answer me? every one know, please just tell me.

[mateen_maldar]

hi,

check the email example for easy of receiving an email .u have to explictly code for the sending part of the email.

http://www.forum.nokia.com/info/sw.n..._v1_1.zip.html

Regards,
Mateen Maldar

[xhsoldier]

But, can you tell me
Is it possible to send email using rsendas and rsendasmessage?
and how to do it?
thanks a lot

hi,

check the email example for easy of receiving an email .u have to explictly code for the sending part of the email.

http://www.forum.nokia.com/info/sw.n..._v1_1.zip.html

Regards,
Mateen Maldar

[mateen_maldar]

hi,

AFAIk for sending or receiving emails u have to configure ur POP3 or IMAP4 connection.Coz similar to the access points defined to sms , one has to confire for POP3 or IMAp4 so i didn't tried with RSendMessage coz it has no scope for direct access for the connections of emails.

so check the email example and make ur own code for send emails.

Regards,
Mateen Maldar

[mateen_maldar]

hi,

this is the release notes of email example

PRECONDITIONS AND CONFIGURATION


The following settings must be configured for the example application:

Internet access point with TCP/IP (note that WAP settings are not
sufficient). The Internet access point is usually received from the operator.
It might even be a built-in feature of the device (such as in the Nokia 6600
in some countries), or it can be set manually in the device’s control panel
from Tools->Settings->Connections->Access points. If necessary, refer to the
user’s guide of the device.

IMAP/POP settings in the built-in messaging application:
Messaging->Mailbox->Settings.

NOTE 1: This example application always uses the first IMAP and/or POP
service entry that has been set. This means that you can have more than one
service entry of each type but only the first one of the given type is used.

NOTE 2: The minimum e-mail service settings you need are username,
password, and the URL of the receiving server. The protocol type must be
either IMAP or POP. All other fields can contain the default value or any
strings. However, the configuration must correspond with the used e-mail
server and the features it supports. If you want to send e-mail using the
generic view, remember also to set the sending server, which should be the
SMTP server.

Regards,
Mateen Maldar

[xhsoldier]

I have successfully sent and received email using the accounts set by the user(local service).

How do I send email without using any email account?

[xhsoldier]

go on asking

[mateen_maldar]

hi,
i didn't get u wht u mean by the message u posted...

go on asking

Regards,
Mateen Maldar

[xhsoldier]

just as before, I want to know how to send and recieve email using RSendAs and RSendAsMessage?
better for some exzmple, there is no example at all.

hi,
i didn't get u wht u mean by the message u posted...



Regards,
Mateen Maldar

[fvancaen]

use

const TUid KUidMsgTypeSMTP= {0x10001028};

and it ll work
rgds
frank

[fvancaen]

it s in
#include <miutset.h>
rgds
frank