Upgradation from carbide.c++ express v1.1 to carbide.c++ express v1.2

[rkambika]

hi,

I have installed carbide.c++ express v1.1 for s60 application development. Now i want to install the later version of carbide(carbide.c++ express v1.2).
Can anyone tell me the installation procedure of carbide.c++ express v1.2?

Do i need to re-install the older version before the installation of new one? If re-installation is not needed, how to install the new one?

Kindly give me a solution.

Thanks in advance,
Ambika.

[Symbian_Neil]

hi,

I have installed carbide.c++ express v1.1 for s60 application development. Now i want to install the later version of carbide(carbide.c++ express v1.2).
Can anyone tell me the installation procedure of carbide.c++ express v1.2?

Do i need to re-install the older version before the installation of new one? If re-installation is not needed, how to install the new one?

Kindly give me a solution.

Thanks in advance,
Ambika.

Hi Ambika,

I have installed carbide 1.2 in a seperate directory as a seperate installation. Its working fine for me.

No need to re-install the older version before installation of new one. Just install the new one the way you had done the old one(i didnt quite get what you meant how to install the new one..I presume you installed the old one, this one follows the same procedure)

Good Luck and Cheers
Neil

[rkambika]

hi,

Thank you for your reply. I got some error when i installed the old one. Thats why i wanted to know, Is there any specific installation procedure for this tool?

Anyway, thank you once again,
Ambika.

[Symbian_Neil]

hi,

Thank you for your reply. I got some error when i installed the old one. Thats why i wanted to know, Is there any specific installation procedure for this tool?

Anyway, thank you once again,
Ambika.

Hi Ambika,

Well, there should not be any error really. But if you could have told what error, and more details regarding at what stage etc, its easier to understand why that error could have occured.

But anyway, good luck with your new installation(install in new directory)

cheers
Neil

[rkambika]

Hi Neil,

As You told, I have installed the later version of carbide(carbide.c++ express v1.2). I tried to build the Helloworld application, but the build had failed and showed the following error message:

perl are not considered as internal and external command.

Earlier I had ActivePerl 5.8.8 version in my system. When i installed carbide.c++ express v1.2, the installation was not completed because of this ActivePerl version. So, I uninstalled the ActivePerl old version and installed with ActivePerl 5.6.1 Build 635.

According to some suggestions in forum posts, i checked in command prompt for perl. I typed perl -v in command prompt. There also i found the same error.

Can you please give me suggestions to solve this problem.

Thanks in advance,
Ambika.

[amitkankani]

this means ur pearl path is not set...

where have u installed perl... say c:\perl

then in the path variable you have to include the following :
c:\perl\bin

how to modify the path varuiable... :

right click on My Computer -> Advanced Tab -> Environment Variables -> User Variables -> Path

Make sure there is a semi colon (";") between each path u add.. i.e. oldpath;c\perl\bin\;

after this press ok and then only open a new command prompt and say perl.. and see what u get ! this shud solve the prob !

good luck !

[rkambika]

Hi Amit,

Thank you for your reply. I had installed ActivePerl properly and path was mentioned automatically. But I did mistake in the installation path. I installed it in E drive instead of C drive. Now i installed it in proper path and the problem was solved.

Thank you once again,
Ambika.