error in carbide

[nayan_trivedi]

when i m going to run qt project in carbide c++.
that is error with widget that.
" No SDK's were found that contain Qt support"

i already have install S60_3rd_FP2_Beta

[A.A.M.]

Are you have already installed & configured Qt for S60 SDK (as described here - http://pepper.troll.no/s60prerelease...stall-s60.html)?

[nayan_trivedi]

Are you have already installed & configured Qt for S60 SDK (as described here - http://pepper.troll.no/s60prerelease...all-s60.html)?

i can't open your link.
i have install qt.

but at the end that is error
"cleaning qmake file . code error 255

[james1980]

Hi nayan,
before installing qt make sure that your carbide is configure for winscw enviroment. You can find it at
start-programs-carbide c++-configure for winscw.

Than only you can configure the qt .
Regards.

[Sorcery-ltd]

The link has been fixed. SDKs will only show as having Qt support when you've successfully installed the Qt libraries for the target to them and/or built Qt for the Windows emulator using them.

Mark

[A.A.M.]

http://pepper.troll.no/s60prerelease...stall-s60.html

Link fixed.

[nayan_trivedi]

Hi nayan,
before installing qt make sure that your carbide is configure for winscw enviroment. You can find it at
start-programs-carbide c++-configure for winscw.

Than only you can configure the qt .
Regards.

hi..sir
i have already done it.
but error
""cleaning qmake file . code error 255"
remains same.

[nayan_trivedi]

Link fixed.

i have done all this but after that error
""cleaning qmake file . code error 255"
occurs.

[A.A.M.]

i already have install S60_3rd_FP2_Beta

I'm not sure but may be S60 SDK with status "Beta" is unsupported.

As reffered in this post:

S60 SDKs that can be used for Qt development on S60
* 3rd Edition FP1 http://www.forum.nokia.com/info/sw.n...16-3.0-mr.html
* 3rd Edition FP2 and 5th Edition http://www.forum.nokia.com/info/sw.n..._One_SDKs.html

[mind_freak]

hi nayan
james1980 is right first of all go for start->all programs->carbid c++ ->configure for winscw enviroment
after doing this much of work configure ur QT SRC so that all the files that are needed for running the the QT Application in the command prompt and also used in configuring QT with Carbid C++

[Sorcery-ltd]

I'm not sure but may be S60 SDK with status "Beta" is unsupported.

The beta SDK should work but it would be better to upgrade to the official release.

Mark

[james1980]

hi nayan,

I think there is a problem with the version of the SDK so try to get new official release or 5th edition SDK.
Hope it works for you.

Regards.

[mind_freak]

hi
i think you go for both carbid v2.0 and SDK FP2 (insatallation of "jre" and perl is must)

Regards
Viral Parmar

[cbrandt]

when i m going to run qt project in carbide c++.
that is error with widget that.
" No SDK's were found that contain Qt support"

i already have install S60_3rd_FP2_Beta

I have the same problem.

[Symbian_Neil]

I have the same problem.

Same problem doesnt say much. But anyway, you could check by typing in commandline 'devices' if it shows your SDK installed. If so, add the SDK in the carbide. Check help in carbide to do that.